Fibaro Roller Shutter Specifications download pdf (Page 1)

ENG

Fibaro Roller Shutter is a universal, Z-Wave compatible, electric

motor controller. The device allows for controlling motors of roller

blinds, awnings, venetian blinds, gates and others, which are single

phase AC powered. Fibaro Roller Shutter allows for precise

positioning of a roller blind or venetian blind lamellas. Precise

positioning is available for the motors equipped with mechanic and

electronic end switches.

The module may be controlled wirelessly, through the Z-Wave

network main controller, or through the switch keys connected to it.

It’s also possible to combine few devices into groups of devices,

which then can be controlled simultaneously. In addition, Fibaro

Roller Shutter is equipped with Power Metering.

SPECIFICATIONS

Power Supply

Supplied motor type

Supported limit switches type

Power of supplied motor

In accordance

with EU standards

Circuit Temperature limit

Operational Temperature

For installation in boxes

Radio protocol

Radio Frequency

Radio signal power

Range

Dimensions (L x W x H)

Electricity consumption

110 - 230 V ±10% 50/60Hz

Single phase, VAC

Electronic and mechanic

up to 1kW for 230V

up to 500W for 110V

LVD (2006/95/EC)

EMC (2004/10B/EC)

R&TTE(1999/5/EC)

105 °C

0 - 40 °C

Ø ≥ 50mm

Z-Wave

868,4 MHz EU;

908,4 MHz US;

921,4 MHz ANZ;

869,2 MHz RU;

1mW

up to 100m outdoors

up to 30m indoors

(depending on building materials

used)

42 x 37 x 17 mm

< 0,8W

TECHNICAL INFORMATION

• Controlled by Fibaro System devices or any Z-Wave controller

• Microprocessor control

• Executive elements: relays

• The device may be operated by momentary or toggle switches,

and by dedicated roller blind control switches

• Connected motor’s current and historical power consumption

measured

WARNING

Danger of electrocution! Any work on the device

regarding electrical connections may be performed

only after the power supply has been

disconnected.

OPERATING MANUAL

FIBARO ROLLER SHUTTER

FGRM-222 v2.1 - v2.3

I. GENERAL INFORMATION ABOUT FIBARO SYSTEM

Fibaro is a wireless system, based on Z-Wave technology. Fibaro

provides many advantages when compared to similar systems. In

general, radio systems create a direct connection between the

receiver and transmitter. However, a radio signal is weakened by

various obstacles located in its path (apartment walls, furniture,

etc.) and in extreme cases it fails to transfer required data. The

advantage of Fibaro System is that its devices, apart from being

transmitters and signal receivers, also duplicate signal. When a

direct connection path between the transmitter and the receiver

cannot be established, the connection may be achieved through

other intermediate devices.

Fibaro is a bi-directional wireless system. This means that the

signal is not only sent to the receivers but also the receivers send

the confirmation of its reception. This operation confirms their

status, which checks whether they are active or not. Safety of the

Fibaro System transmission is comparable to the safety of

transmission in data bus wired systems.

Fibaro operates in the free bandwidth for data transmission. The

frequency depends on radio regulations in individual countries.

Each Fibaro network has its own unique network identification

number (home ID), which is why it is possible to co-operate two or

more independent systems in a single building without any

interference.

Although Z-Wave is quite a new technology, it has already become

recognized and officially a binding standard, similarly to Wi-Fi.

Many manufacturers in various industries offer solutions based on

Z-Wave technology, guaranteeing their compatibility. This means

that the system is open and it may be extended in the future. Find

more information at www.fibaro.com.

Fibaro generates a dynamic network structure. After Fibaro System

is switched on, the location of its individual components is

automatically updated in real-time through status confirmation

signals received from devices operating in a "mesh" network.

II. ROLLER SHUTTER INSTALLATION

1. Before installation make sure the voltage supply is

disconnected.

2. Connect the Roller Shutter in accordance with the wiring

diagram presented on Fig. 1 (roller blinds, venetian blinds) or

Fig. 2 (gates).

3. Place the device in a switch box.

4. Arrange the antenna (tips presented below Fig.2)

5. Turn on the power supply keeping the necessary safety

precautions.

6. Include the module into the Z-Wave network, observing pt. III

description.

7. If necessary, calibrate the module, observing pt. VI descripion.

NOTES FOR THE DIAGRAM:

L - terminal for live lead

N - terminal for neutral lead

S1 - terminal for key no. 1 (has the option of entering the device in

learning mode)

S2 - terminal for key No. 2

O1 - output terminal no. 1 for shutter motor

O2 - output terminal no. 2 for shutter motor

B - service button (used to add or remove a device from the

system)

ROLLER BLIND POSITIONING CALIBRATION

TIPS FOR ARRANGING THE ANTENNA

1. Locate the antenna as far from metal elements as possible

(connection wires, bracket rings, etc.) in order to prevent

interferences.

2. Metal surfaces in direct vicinity of the antenna (e.g. metal switch

boxes, door frames) may impair radio signal reception!

3. Do not cut or shorten the antenna. Its length is perfectly

matched to the band in which the system operates.

NOTE

A push button connected to S1 terminal operates

the O1 output, while the push button connected to

S2 terminal operates the O2 output. It’s recommen-

ded to connect an UP button to S1 terminal and a

wire, responsible of up movement, to O1 output

terminal. Respectively, a DOWN button should be

connected to S2 terminal and a wire, responsible

for down movement, to O2 output terminal.

WARNING

Fibaro Roller Shutter is dedicated to operate with

AC powered electric motors. Connecting the device

directly to DC powered motors may result in them

being damaged.

Fig. 3 Roller Shutter icons in Home Center interface

WARNING

Danger of electrocution! Even when the device is

turned off, voltage may be present at it’s terminals.

Any work on the device regarding electrical

connections may be performed only after the

power supply has been disconnected.

WARNING

Any maintenance work on controlled devices may

be performed only after the power supply has been

disconnected.

WARNING

It’s not recommended to operate all of the roller

blinds simultaneously. For safety reasons, at least

one roller blind should be controlled independently,

providing safe escape route in case of emergency.

WARNING

Do not connect the device to loads exceeding

recommended value.

Fig. 1 Roller Shutter wiring diagram

III. Z-WAVE NETWORK INCLUSION

Fibaro Roller Shutter may be included into the Z-Wave network via

the B-button or a push button connected to the S1 terminal. In

addition, the module may be included in auto inclusion mode, by

simply connecting the power supply.

Automatic Z-Wave network inclusion:

1) Make sure the power supply is disconnected and a Roller Shutter

is located within a direct Z-Wave network’s main controller

communication range.

2) Set the main controller into the learn mode (see main controllers

operating manual).

3) Connect the power supply to include the Roller Shutter in auto

inclusion mode.

4) Fibaro Roller Shutter will be automatically detected and included

into the Z-Wave network.

To disable the auto inclusion mode, press the B-button briefly, after

connecting the module to the power supply.

Manual Z-Wave network inclusion:

1) Connect the power supply.

2) Set the main controller into the learn mode (see main controllers

operating manual).

3) Triple click the B-button or a push button connected to the S1

terminal.

4) Fibaro Roller Shutter will be detected and included into the

Z-Wave network.

IV. Z-WAVE NETWORK EXCLUSION

Excluding Fibaro Roller Shutter from the Z-Wave network:

1) Make sure the module is connected to the power supply.

2) Set the main controller into the learn mode (see main controllers

operating manual).

3) Triple click the B-button or a push button connected to the S1

terminal.

V. ROLLER SHUTTER RESET

Reset procedure clears the modules’ EPROM memory, including all

information about the Z-Wave network controller, calibration and

power consumption data.

1) Make sure the module is connected to the power supply.

2) Press and hold the B-button for ca. 14 seconds.

3) LED indicator will glow yellow.

4) Release the B-button and press it again, briefly.

5) The Roller Shutter memory is now empty.

6) The module goes into the auto inclusion mode, until any button

is pushed.

NOTE

Memory reset does not remove the module from

the Z-Wave network main controller’s memory.

Prior to memory reset it’s recommended to exclude

the module from the Z-Wave network.

TIP

After memory reset, the Roller Shutter goes into the

auto inclusion mode and waits to be included into

the Z-Wave network. To exit the auto inclusion

mode press the B-button briefly.

Fig. 2 Connecting Roller Shutter to GATE motor

VI. POSITIONING CALIBRATION

Calibration is a process during which a Roller Shutter learns the

position of the limit switches and a motor characteristic. Calibration

is mandatory in order for the Roller Shutter to correctly recognize a

roller blind position. The procedure consists of an automatic, full

movement between the limit switches (up, down, and up again).

There are separate procedures of calibrating roller blind and

lamellas (venetian blind) positioning. Each time the calibration

requires the completion of a full cycle (up and down).

There are 5 procedures of calibrating a Fibaro Roller Shutter to

choose from. Each one gives the same results and the user may

choose which one to execute.

A. Calibration through a Fibaro Home Center 2 interface

1) Make sure the module is connected to the power supply,

according to Fig.1

2) Include the module into the Z-Wave network, according to

section

III of instructions.

3) In Home Center 2 interface choose Fibaro Roller Shutter’s

advanced settings.

4) Click CALIBRATE buttin in the devices advanced settings tab.

5) Roller Shutter performs the calibration process, completing full

cycle - up, down and up again.

6) Using an interface test whether the positioning works correctly.

B. Calibration through the Z-Wave network

1) Make sure the module is connected to the power supply,

according to Fig.1

2) Include the module into the Z-Wave network, according to pt.III

instructions.

3) Set the parameter 29 value to 1.

4) Roller Shutter performs the calibration process, completing full

cycle - up, down and up again.

5) The parameter 29 value will be automatically set to 0.

6) Using an interface test whether the positioning works correctly.

C. Calibration through the switch keys

1) Make sure the module is connected to the power supply,

according to Fig.1, and to the switch keys as well (S1 and S2

inputs).

2) Include the module into the Z-Wave network, according to

section

III of instructions.

3) Press and hold the switch key connected to S1 or S2 input

terminal and release it after at least 3 seconds.

4) Press and hold the same switch key again, and release it after 3

seconds.

5) Now press and hold the same button, for 3 seconds, for the 3rd

time.

6) After pressing and releasing the button for the third time,

automatic calibration sequence will start.

7) Roller Shutter performs the calibration process, completing full

cycle - up, down and up again.

D. Calibration through Menu (B-button)

1) Make sure the module is connected to the power supply,

according to Fig.1

2) Include the module into the Z-Wave network, according to

section

III of instructions.

3) Press and hold the B-button for ca. 6 seconds.

4) LED will glow blue.

5) Release the B-button and press it again, briefly.

6) Roller Shutter performs the calibration process, completing full

cycle - up, down and up again.

CALIBRATING LAMELLAS POSITIONING

IN VENETIAN BLINDS

Apart from calibrating the roller blind position, it’s possible to

calibrate the position of venetian blinds lamellas. After correct

calibration, in case of venetian blinds, it’s possible to set the position

between the limit switches, as well as the lamellas angle. By default,

time of full turn of the lamellas is set to 1,5 seconds. If necessary, it

can be modified following below instructions.

1) Make sure the module is connected to the power supply,

according to Fig.1

2) Include the module into the Z-Wave network, according to section

III of instructions.

3) Calibrate the Roller Shutter, according to the instructions

provided in sections VI.A, VI.B, VI.C, VI.D or VI.E.

4) Set the parameter 10 value to 2 or choose in HC2 interface:

Device Type - Venetian Blind

5) Another device icon, responsible for lamellas operation, will show

up in Home Center 2 interface. In case of any other Z-Wave

network controllers managing the lamellas position is achieved

through pressing and holding a switch key (up or down).

6) By default, time of transition between extreme positions is set to

1 500 ms (1,5 seconds).

7) Turn lamellas between extreme positions. If after full cycle a blind

starts moving up or down, then parameter’s 12 value must be

modified, e.g. to 1 000ms (1 second). Correctly configured

lamellas should not force the blind to move up or down.

NOTE

Roller Shutter needs to be calibrated to work with

any given motor.

NOTE

In Venatian Blind mode, lamellas need to be

calibrated to work with any given motor.

VII. OPERATING THROUGH THE Z-WAVE NETWORK

After including into the Z-Wave network, Fibaro Roller Shutter will

be presented in a Home Center 2 interface as a roller blind icon (see

fig. below). After choosing Venetian Blind device type, a second icon

will show up, responsible for managing lamellas position.

User can choose from the following operating modes:

1. Roller Blind Mode, without positioning

2. Roller Blind Mode, with positioning

3. Venetian Blind Mode

4. Gate Mode, without positioning

5. Gate Mode, with positioning

After choosing one of the above operating modes, device will be

represented in Home Center 2 interface by icons shown in Fig.4. In

addition, each operating mode affects certain parameters settings:

1) Roller blind without positioning (parameter 10 set to 0)

2) Roller blind with positioning (parameter 10 set to 1)

3) Venetian blind (parameter 10 set to 2; parameter 13, set to 2)

4) Gate without positioning (parameter 10 set to 3; parameter 12 set

to 0; parameter 17 set to 0)

5) Gate with positioning (parameter 10 set to 4; parameter 12 set to

0; parameter 17 set to 0)

Opening / Closing a blind is acheved through moving a slider or

pushing a button shown in fig. 3.

In Venetian Blind mode, setting lamellas angle is achieved through

moving a slider or pushing a button shown in fig. 3.

VIII. MANUAL OPERATION

Fibaro Roller Shutter allows for connecting push buttons to S1 and

S2 terminals. These may be momentary or toggle switches,

alternatively. Push buttons are responsible for managing the blind’s

movement.

Using momentary switches:

Clicking button connected to S1 terminal, initiates up

movement.

Clicking button connected to S2 terminal, initiates down

movement.

If the blind is moving, each click, of any button, will stop the

movement. In addition a button click sends a command frame to I-st

association group devices.

In case of venetian blinds, it’s possible to manage the lamellas

angle. Operating Mode - Venetian Blind, or Parameter 10 value set

to 2.

Holding connected to S1 terminal initiates lamellas rotation up.

Holding connected to S2 terminal initiates lamellas rotation

down.

In addition a button hold sends a Fibar Command Class control

frame to II-nd association group devices.

IX. ASSOCIATIONS

Through an association Fibaro Roller Shutter may control another

Z-Wave network device, e.g. another Roller Shutter, Wall Plug,

Dimmer, Relay Switch, RGBW Controller.

NOTE

Association allows for direct communication

between Z-Wave network devices. Main controller

does not take part in such communication.

Fibaro Roller Shutter provides three association groups:

I association group is triggered through a momentary switch click,

or a toggle switch position change.

II association group is triggered through a momentary switch hold

NOTE

II association group is inactive when toggle

switches are used or in Gate Controller mode

(parameter 10). In case of controlling Venetian

Blinds, control commands are sent in Fibar

Command Class standard.

III association group reports the module status. Only one device

may be assigned to this group, main controller by default. It’s not

recommended to modify this group’s settings.

Fibaro Roller Shutter allows for commanding other Roller Shutters,

associated into I or II association group, through clicking or holding

a switch key. For example, this mechanism allows for operating a

Roller Shutter connected to the switch with a button click, and

operating the devices associated in II association group by a button

hold. In addition, when operating Venetian Blinds, it’s possible to

synchronize many devices.

USING ASSOCIATIONS TO OPERATE ANOTHER

ROLLER SHUTTER OR ANY OTHER Z-WAVE

DEVICE.

I ASSOCIATION GROUP:

Clicking button, connected to S1 terminal will initiate up

movement in associated Roller Shutters, or send Turn On command

frame to the devices associated in I-st association group.

Clicking button, connected to S2 terminal will initiate down

movement in associated Roller Shutters, or send Turn Off command

frame to the devices associated in I-st association group.

II ASSOCIATION GROUP:

Holding button, connected to S1 terminal will move the

connected roller blind up, and after 1 second delay initiate up

movement in associated Roller Shutters, or send Turn On command

frame to the devices associated in II-nd association group.

Holding button, connected to S2 terminal will move the

conected rolled blind down, and after 1 second delay initiate down

movement in associated Roller Shutters, or send Turn Off command

frame to the devices associated in II-nd association group.

NOTE

To abort the calibration process press any key

(connected to S1 or S2) or send a STOP control

frame through the Z-Wave network controller. In

Gate Controller mode the calibration process will

be aborted after disconnecting the S2 terminal.

Using toggle switches:

Changing switch key position, connected to S1 terminal,

initiates up movement.

Changing switch key position, connected to S2 terminal,

initiates down movement.

Choosing a middle position stops the blind.

NOTE

Venetian blind lamellas may be only operated by

momentary switches.

NOTE

Above operating modes and their default settings

are modified automatically only in Home Center 2

controller. In case of the Z-Wave network

controllers from other manufacturers, these

settings need to be manually adjusted (see section

XV).

L NS1 S2

O2 O1

safety switch

sensor

Fibaro Roller

Shutter

limit

switches

E. Calibration through a Fibar Command Class control frame.

It’s possible to force the calibration process execution through

sending a Fibar Command Class control frame through a Z-Wave

network main controller (see a Fibar Command Class documenta-

tion).

WARNING

It is recomended to monitor regulary operation of

Fibaro Roller shutter in all modes. In case of gate

control mode device, motor limit switches, infrared

barriers and emergency stop should be monitored

and maintained regulary

USING ASSOCIATIONS TO OPERATE ROLLER

SHUTTERS CONNECTED TO VENETIAN BLINDS.

Using association mechanism to operating venetian blinds requires

configuring both, I-st and II-nd association groups.

I ASSOCIATION GROUP

Clicking button, connected to S1 terminal will initiate up

movement of the connected venetian blind and other devices

associated in I-st association group.

Fibaro Roller

Shutter

L NS1 S2

1 2

Summary of Contents

Page 1 - FGRM-222 v2.1 - v2.3

ENGFibaro Roller Shutter is a universal, Z-Wave compatible, electric motor controller. The device allows for controlling motors of roller blinds, awni

Page 2 - FIBARGROUP

Clicking button, connected to S2 terminal will initiate down movement of the connected venetian blind and other devices associated in I-st ass

Comments to this Manuals

No comments

Fibaro Roller Shutter Specifications Page 1

Browse online or download Specifications for Remote power controllers Fibaro Roller Shutter. Fibaro Roller Shutter User Manual

Summary of Contents

Comments to this Manuals