Fibaro FGWPF-101 Specifications download pdf (Page 2)

1. The Guarantee is provided by FIBAR GROUP Sp. z o.o.

(hereinafter "Manufacturer"), based in Poznan, ul. Lotnicza 1; 60-421

Poznan, entered in the register of the National Court Register kept

by the District Court in Poznań, VIII Economic Department of the

National Court Register, no. 370151, NIP 7811858097, REGON:

301595664.

2. The Manufacturer is responsible for equipment malfunction

resulting from physical defects (manufacturing or material) of the

Device for 12 months from the date of its purchasing.

3. During the Guarantee period, the Manufacturer shall remove any

defects, free of charge, by repairing or replacing (at the sole

discretion of the Manufacturer) any defective components of the

Device with new or regenerated components, that are free of

defects. When the repair impossible, the Manufacturer reserves the

right to replace the device with a new or regenerated one, which shall

be free of any defects and its condition shall not be worse than the

original device owned by the Customer.

4. In special cases, when the device cannot be replaced with the

device of the same type (e.g. the device is no longer available in the

commercial offer), the Manufacturer may replace it with a different

device having technical parameters similar to the faulty one. Such

activity shall be considered as fulfilling the obligations of the

Manufacturer. The Manufacturer shall not refund money paid for the

device.

5. The holder of a valid guarantee shall submit a guarantee claim

through the guarantee service. Remember: before you submit a

guarantee claim, contact our technical support using telephone or

e-mail. More than 50% of operational problems is resolved remotely,

saving time and money spent to initiating guarantee procedure. If

remote support is insufficient, the Customer shall fill the guarantee

claim form (using our website - www.fibargroup.com) in order to

obtain claim authorization.

When the guarantee claim form is submitted correctly, the Customer

shall receive the claim confirmation with an unique number (Return

Merchandise Authorization -RMA).

6. The claim may be also submitted by telephone. In this case, the

call is recorded and the Customer shall be informed about it by a

consultant before submitting the claim. Immediately after submitting

the claim, the consultant shall provide the Customer with the claim

number (RMA-number).

7. When the guarantee claim form is submitted correctly, a

representative of the Authorised Guarantee Service (hereinafter as

"AGS") shall contact the Customer.

XI. Guarantee

NOTE

This functionality is not an overload safety

protection nor a short circuit protection. Circuit

needs additional short circuit and overload

protection.

ASSOCIATION GROUP 2

COLOUR SETTINGS

SAFETY

This Device may be used with all devices

certified with Z-Wave certificate and should be

compatible with such devices produced by

other manufacturers.

Any device compatible with Z-Wave may be added

to Fibaro system.

FIBARGROUP

FIBARO

In case of any technical questions contact customer service centre

in your country.

www.fibargroup.com

8. Defects revealed within the guarantee period shall be removed

not later than 30 days from the date of delivering the Device to AGS.

The guarantee period shall be extended by the time in which the

Device was kept by AGS.

9. The faulty device shall be provided by the Customer with complete

standard equipment and documents proving its purchase.

10. Parts replaced under the guarantee are the property of the

Manufacturer. The guarantee for all parts replaced in the guarantee

process shall be equal to the guarantee period of the original device.

The guarantee period of the replaced part shall not be extended.

11. Costs of delivering the faulty device shall be borne by the

Customer. For unjustified service calls, the Service may charge the

Customer with travel expenses and handling costs related to the

case.

12. AGS shall not accept a complaint claim only when:

• the Device was misused or the manual was not observed,

• the Device was provided by the Customer incomplete, without

accessories or nameplate,

• it was determined that the fault was caused by other reasons than

a material or manufacturing defect of the Device

• the guarantee document is not valid or there is no proof of

purchase,

13. The Manufacturer shall not be liable for damages to property

caused by defective device. The Manufacturer shall not be liable for

indirect, incidental, special, consequential or punitive damages, or

for any damages, including, inter alia, loss of profits, savings, data,

loss of benefits, claims by third parties and any property damage or

personal injuries arising from or related to the use of the Device.

14. The guarantee shall not cover:

• mechanical damages (cracks, fractures, cuts, abrasions, physical

deformations caused by impact, falling or dropping the device or

other object, improper use or not observing the operating manual);

• damages resulting from external causes, e.g.: flood, storm, fire,

lightning, natural disasters, earthquakes, war, civil disturbance, force

majeure, unforeseen accidents, theft, water damage, liquid leakage,

battery spill, weather conditions, sunlight, sand, moisture, high or low

temperature, air pollution;

• damages caused by malfunctioning software, attack of a computer

virus, or by failure to update the software as recommended by the

Manufacturer;

• damages resulting from: surges in the power and/or telecommuni-

cation network, improper connection to the grid in a manner

inconsistent with the operating manual, or from connecting other

devices not recommended by the Manufacturer.

• damages caused by operating or storing the device in extremely

adverse conditions, i.e. high humidity, dust, too low (freezing) or too

high ambient temperature. Detailed permissible conditions for

operating the Device are defined in the operating manual;

• damages caused by using accessories not recommended by the

Manufacturer

• damages caused by faulty electrical installation of the Customer,

including the use of incorrect fuses;

• damages caused by Customer's failure to provide maintenance and

servicing activities defined in the operating manual;

• damages resulting from the use of spurious spare parts or

accessories improper for given model, repairing and introducing

alterations by unauthorized persons;

• defects caused by operating faulty Device or accessories.

15. The scope of the guarantee repairs shall not include periodic

maintenance and inspections, in particular cleaning, adjustments,

operational checks, correction of errors or parameter programming

and other activities that should be performed by the user (Buyer).

The guarantee shall not cover natural wear and tear of the Device

and its components listed in the operating manual and in technical

documentation as such elements have a defined operational life.

16. If a defect is not covered by the guarantee, the Manufacturer

reserves the right to remove such defect at its sole discretion,

repairing the damaged or destroyed parts or providing components

necessary for repair or replacement.

17. This guarantee shall not exclude, limit or suspend the Customer

rights when the provided product is inconsistent with the purchase

agreement.

42. Standard power load reporting.

Parameter defines by how much power load must change, in

percents, to be reported to the main controller. By default, Fibaro

Wall Plug sends power report if the power load changes by 15%.

By default such changes in power load may be reported up to 5 times

per 30 seconds. Wall Plug sends 5 reports during time period

specified in paramater 43.

Default setting: 15 (%)

Available settings: 1 - 100 (%)

Value of 100 (%) means the reports are turned off.

Parameter: 1[byte]

43. Power reporting frequency.

This parameter defines how frequently standard power reports

(parameter 42) will be sent. By default Wall Plug sends up to 5

reports each 30 seconds, provided the power load changes by 15%.

Default seting: 30 (s)

Available settings: 1 - 254 (s)

Value of 255 - Reports will be sent only as a result of parameter 47

settings or in case of polling.

Parameter: 1[byte]

45. Reporting changes in energy consumed by controlled

devices

New, reported energy value is calculated based on last reported

value. Default setting: 10 (0,1 kWh).

Available settings: 1 - 254 (0,01kWh - 2,54kWh).

Value of 255 - changes in consumed energy will not be reported.

Reports will be sent only in case of polling.

Parameter: 1[byte]

61. LED ring illumination colour when controlled device is on.

Default value: 1

Available settings:

0 - LED ring illumination colour changes in predefined steps,

depending on power consumption changes,

1 - LED ring illumination colour changes continuously, using full

spectrum of available colorus, depending on power consumption

changes.

2 - White illumination,

3 - Red illumination,

4 - Green illumination,

5 - Blue illumination,

6 - Yellow illumination,

7 - Cyan (Greenish blue) illumination,

8 - Magenta (Purplish red) illumination,

9 - illumination turned off completely.

Parameter: 1[byte]

62. LED ring illumination color when controlled device is off.

Default setting: 8

Available settings:

0 - LED ring is illuminated with a color corresponding to the last

measured power, before the controlled device was turned off,

1 - White illumination,

2 - Red illumination,

3 - Green illumination,

4 - Blue illumination,

5 - Yellow illumination,

6 - Cyan (Greenish blue) illumination,

7 - Magenta (Purplish red) illumination,

8 - illumination turned off completely.

Parameter: 1[byte]

70 . Oveload safety switch

This function allows for turning off the controlled device in case of

exceeding the defined power. Controlled device will be turned off

even if "always on" function is active (parameter 1).

Controlled device can be turned back on via B-button or sending a

control frame. By default this function is inactive.

Default setting: 65 535 (6 553,5W)

Available settings: 10 - 65 535 (1W - 6 553,5W).

Value higher than 32 000 (3 200W) turns the overload safety switch

off, i.e. this functionality is turned off by default.

Parameter: 2[byte]

49. Metering energy consumed by the Wall Plug itself.

This parameter determines whether energy metering should include

the amount of energy consumed by the Wall Plug itself.

Results are being added to energy consumed by controlled device.

Default setting: 0

Available settings:

0 - function inactive,

1 - function activated.

Parameter: 1[byte]

Status of devices added to 2nd Association Group may depend on

power consumed by the connected device. For example, turning on

the TV controlled by the Plug will turn off the lights in the room.

User defines two thresholds: UP and DOWN, and then defines the

reaction to them being exceeded (parameter 52).

50. DOWN value

Lower power threshold, used in parameter 52.

Default setting: 300 (30 W)

Available settings: 0 - 25 000 (0,0W - 2 500W)

DOWN value cannot be higher than a value specified in parameter

51.

Parameter: 2[byte]

51. UP value

Upper power threshold, used in parameter 52.

Default setting: 500 (50 W)

Available settings: 1 - 25 000 (0,1W - 2 500W)

UP value cannot be lower than a value specified in parameter 50.

Parameter: 2[byte]

60. Power load, which when exceeded, makes the LED ring

flash violet.

Function is active only when parameter 61 is set to 0 or 1.

Default setting: 25 000 (2 500W)

Available settings: 1 000 - 32 000 (100W - 3200W).

Parameter: 2[byte]

52. Action in case of exceeding defined power values

(parameters 50 and 51)

Parameter deifines the way 2nd association group devices are

controlled, depending on the current power load.

Default setting: 6

Available settings:

0 - function inactive,

1 - turn the associated devices on, once the power drops below

DOWN value (parameter 50),

2 - turn the associated devices off, once the power drops below

DOWN value (parameter 50),

3 - turn the associated devices on, once the power rises above UP

value (parameter 51),

4 - turn the associated devices off, once the power rises above UP

value (parameter 51),

5 - 1 and 4 combined. Turn the associated devices on, once the

power drops below DOWN value (parameter 50). Turn the

associated devices off, once the power rises above UP value

(parameter 51).

6 - 2 and 3 combined. Turn the associated devices off, once the

power drops below DOWN value (parameter 50). Turn the

associated devices on, once the power rises above UP value

(parameter 51).

Parameter: 1[byte]

47. Time period between reports on power load and energy

consumption.

Parameter defines time period between reports sent when changes

in power load have not been recorded. By default, if power load

changes have not been recorded, reports are sent every hour.

Default setting: 3 600 (s),

Available settings: 1 - 65534 (s)

Value of 65535 - no periodic reports. Reports will be sent only in

case of power load / energy consumption changes (parameters 40,

42, 43,45) or in case of polling.

Parameter: 2[byte]

63. LED ring illumination colour at the Z-Wave network alarm

detection. Default setting: 1

Available settings:

0 - No change in colour. LED ring illumination colour determined by

parameters 61 or 62 settings,

1 - LED ring flashes red / blue / white (default),

2 - White illumination,

3 - Red illumination,

4 - Green illumination,

5 - Blue illumination,

6 - Yellow illumination,

7 - Cyan (Greenish blue) illumination,

8 - Magenta (Purplish red) illumination,

9 - illumination turned off completely.

Parameter: 1[byte]

1 2

Comments to this Manuals

No comments

Fibaro FGWPF-101 Specifications Page 2

Comments to this Manuals